Elektrine
Log in Register

#voron

10 posts · Last used 23d

Back to Timeline
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jun 17, 2026
Replying to on social.tchncs.de
My Voron Trident is now running! 😀 The printer is accessible via the web interface and so far everything seems fine. The touch screen is disconnected for now, I think something shortened out, it is probably dead. Next up: Going through the initial startup checklist! #voron #trident #3dprinting
6
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jun 17, 2026
Replying to @marginally_constructive@social.tchncs.de
Bed and nozzle can be heated, temperature readings are nominal. The controller fan won't turn on when it should be, but that should be an easy fix... #voron #trident #3dprinting #thermal
2
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 02, 2026
Replying to @marginally_constructive@social.tchncs.de
Panels and doors installed! #voron #trident #3dprinting
2
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 02, 2026
Replying to @marginally_constructive@social.tchncs.de
I removed the protective film from the panels and doors - what a beautiful device! The only item missing is the touch screen at the printer base. The LDO kit also includes a Nevermore kit, which will be installed in the future... #voron #trident #3dprinting
3
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 06, 2026
Replying to @marginally_constructive@social.tchncs.de
Heightmap of the (cold) printbed of my new Voron Trident. Span: 0.169 mm. Not great, not terrible... #voron #trident #3dprinting
3
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 07, 2026
Replying to @marginally_constructive@social.tchncs.de
First print successful! 🎉 #voron #trident #3dprinting #success
8
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 15, 2026
Replying to @marginally_constructive@social.tchncs.de
Finally! The replacement for my broken touchscreen display arrived! #voron #trident #3dprinting
1
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 17, 2026
Replying to @marginally_constructive@social.tchncs.de
The touchscreen display is now installed, KlipperScreen is running and -- after several struggling attempts -- the displays is in the correct orientation! To make a long story short: If you want to use KlipperScreen, it may be best to install RaspberryPi OS and manually install all the Klipper / Moonraker / Mainsail packages... #voron #trident #klipper #klipperscreen #3dprinting
3
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 18, 2026
Replying to @marginally_constructive@social.tchncs.de
For someone who is used to work with a quirky Ender-3, this machine is surprisingly fast... #voron #trident #3dprinting #benchy
1
1
0
marginally_constructive
marginally_constructive @marginally_constructive@social.tchncs.de · Jul 21, 2026
Replying to @marginally_constructive@social.tchncs.de
I installed the Nevermore V5 Duo (activated carbon filter). Mechanical installation and Klipper configuration (printer.conf) was a piece of cake - remembering to install the voltage selection jumper on the controller board not so much... #voron #trident #nevermore #3dprinting
1
1
0

You've seen all posts